抗振条-传热管大间隙多跨直管束流致振动试验研究

针对抗振条-传热管大间隙的4跨传热管直管束开展了流致振动试验研究。传热管束转角正三角形排列，3处抗振条将直管束分为4跨，中间其中1跨的局部区域受到横向流体的冲刷。试验测试获得了管间流速在3.3～14.7 m/s区间内传热管振动位移和振动频率响应特性。结果表明，随着管间流速逐渐增大，传热管在来流方向和升力方向的振动频率依次增大，传热管的振动模态从抗振条1处有效支撑、2处未有效支撑的状态，转换为3处抗振条均有效支撑的状态。试验观测到传热管流弹失稳，其临界流速为14.5 m/s，与5种经验关系式预测结果的对比表明，Chen关系式能较好地预测流弹失稳的发生，预测结果较保守，与试验值间的相对偏差为21.4%。     

1,2,4-trichlorobenzene decomposition using non-thermal plasma technology

Non-thermal plasma(NTP)is regarded as a potential application for environmental pollution control due to its ability to remove pollutants.As a major precursor of dioxins,the influence of the parameters of 1,2,4-trichlorobenzene(TCB)decomposition using NTP technology was investigated through a series of experiments,including voltage,frequency,water content,initial concentration,flow rate,and oxygen content.The experimental results show that the energy injected into the NTP system has a positive correlation to voltage and frequency.Oxygen has the greatest influence on TCB decomposition.The optimal reaction condition was at 15 kV,1000 Hz,an initial concentration of 20 mg m^?3,a flow rate of 2 l min^?1,H2O at 4%,and O2 at 0%.Under this condition,the TCB removal efficiency could reach 92%.According to the generated product backstepping,the hydroxyl radical(·OH)plays an important role in TCB decomposition due to its strong oxidation,which participates in the dechlorination and oxidation reactions as free radicals,and the possible decomposition pathway of TCB by NTP is inferred from the identified byproducts.It is of great significance to investigate the influence of the parameters of TCB decomposition using NTP technology in order to provide references for industrial application.     

高瓦斯矿井U型通风工作面瓦斯治理技术

针对李雅庄煤矿U型通风工作面上隅角及回风流瓦斯浓度高、瓦斯治理难度大的问题，根据工作面瓦斯来源及在采空区三带的运移储存规律，李雅庄煤矿开展了本煤层抽采工艺优化和裂隙带抽采技术研究。对本煤层钻孔封孔深度、联孔工艺、管路连接方式等进行优化，钻孔抽采浓度由抽采4个月后降低到9%提高到抽采10个月后维持在19%；通过调整裂隙带钻孔布置方式、优化钻孔布孔层位、采取下筛管护孔等技术措施，裂隙带钻场最高瓦斯抽采纯流量达13.6 m³/min，平均瓦斯抽采纯流量达8 m³/min，2个钻场联合抽采瓦斯纯流量在13 m³/min以上；取消了瓦斯措施巷、井下移动泵和上隅角风帘，上隅角和回风流平均瓦斯浓度分别控制在0.5%和0.4%以下，对高瓦斯矿井U型通风工作面瓦斯治理有借鉴意义。     

脉冲电流对6016-T4铝合金板材力学性能的影响

为研究在电流辅助成形时脉冲电流的电流密度、占空比和脉冲频率3个因素对6016-T4铝合金板材力学性能的影响规律,设计了3因素5水平的正交实验。实验表明,对6016-T4铝合金力学性能影响的主次因素是:电流密度>占空比>脉冲频率。在此基础上,选用主次2个因素,即电流密度和脉冲频率,使用控制变量法进行进一步的实验研究。实验结果表明,电流密度对6016-T4铝合金力学性能影响较大,改变电流密度的同时带来了明显的焦耳热效应,该效应对材料有明显的软化作用,降低了材料的流动应力,但是,同时也降低了铝合金板的伸长率,这是因为过大的电流密度加剧了试样的主应变演化,进而促进了试样的断裂。而脉冲频率的变化对6016-T4铝合金板材的力学性能影响很小,这也印证了正交实验的结论。     

Comparative analysis of energy absorption behavior of tapered and grooved thin-walled tubes with the various geometry of the cross section

ABSTRACT

In this paper, Crush force efficiency (CFE), Specific Energy Absorption (SEA), Energy Absorption per Crush Length (E_cl), Maximum and average crush forces of straight and grooved tapered thin-walled tubes with various cross-section shapes (circle, ellipse, square, rectangle, hexagon, and octagon) have been studied. The effects of taper, the groove (as initiator) and their interaction have been presented in the current study using Finite Element Method as a numerical method. The tubes have the same volume, height, average cross-section area, thickness and material and have been subjected to axial and oblique dynamic loading. The results of simulations show that the section's geometry, taper and groove addition have a significant effect on energy absorption behavior and the hexagon cross section have better energy absorption behavior compared with other considered geometries. On the other hand, it was found that the behavior of these structures could improve against dynamic axial and oblique impact loading with the cost-effective geometry modifications. These results could help to improve and choose appropriate energy absorber structure based on desirable crush force and energy absorbing characteristics.     

Organic Light-Emitting Diodes: Pushing Toward the Limits and Beyond

Organic light-emitting diodes (OLEDs) are established as a mainstream light source for display applications and can now be found in a plethora of consumer electronic devices used daily. This success can be attributed to the rich luminescent properties of organic materials, but efficiency enhancement made over the last few decades has also played a significant role in making OLEDs a practically viable technology. This report summarizes the efforts made so far to improve the external quantum efficiency (EQE) of OLEDs and discusses what should further be done to push toward the ultimate efficiency that can be offered by OLEDs. The study indicates that EQE close to 58% and 80% can be within reach without and with additional light extraction structures, respectively, with an optimal combination of cavity engineering, low-index transport layers, and horizontal dipole orientation. In addition, recent endeavors to identify possible applications of OLEDs beyond displays are presented with emphasis on their potential in wearable healthcare, such as OLED-based pulse oximetry as well as phototherapeutic applications based on body-attachable flexible OLED patches. OLEDs with fabric-like form factors and washable encapsulation strategies are also introduced as technologies essential to the success of OLED-based wearable electronics.     

基于神经网络和遗传算法的锭子弹性管性能优化

为得到减振弹性管对下锭胆的支承弹性和锭子高速运动下的稳定性等性能的最优匹配效率,依据减振弹性管的等效抗弯刚度及底部等效刚度系数公式,利用MatLab数值分析软件构建弹性管抗弯刚度和底部挠度数学模型。首先,结合Isight优化软件基于径向基神经网络构建其近似模型,且使精度达到可接受水平,并以模型的关键结构参数弹性模量、螺距、槽宽、壁厚为设计变量,结合遗传算法对弹性管抗弯刚度和底部挠度进行多目标优化设计,得到Pareto最优解集和Pareto前沿图,确定出减振弹性管结构工艺参数的优化方案。通过对优化数据进行分析发现,该方案在保证减振弹性管弹性的同时,其底部振幅明显减弱。     

高强铝合金双脉冲VPPA焊缝成形机理

建立双脉冲VPPA(variable polarity plasma arc)焊接系统，进行7A52高强铝合金双脉冲VPPA焊接工艺试验，研究低频脉冲调制叠加高频脉冲对VPPA焊接过程中焊缝成形和焊缝力学性能的影响. 结果表明，低频脉冲周期性振荡液态熔池，可获得表面饱满的鱼鳞纹焊缝；高频脉冲使电弧更为集中，有效地提高了电弧能量密度，穿透力加强；双脉冲耦合振荡加强了对熔池的搅动作用细化了铝合金焊缝晶粒. 焊接接头抗拉强度达到384.13 MPa，相比VPPA焊接接头强度提高了10.21%左右；焊接接头断面收缩率和断后伸长率均有一定程度的提高. 铝合金双脉冲VPPA焊接工艺提高了焊接接头力学性能.     

壳管式相变储能换热器性能研究与场协同效应分析

建立壳管式相变储能换热器仿真模型,利用Fluent软件对蓄能、释能工况分别进行模拟。从温度场、速度场、固液交界面3个方面分析逐时换热强度的变化原因;探讨在蓄热过程中热源管壁温、热管口径规格对传热效率的影响。研究结果表明:蓄热工况下管间热扰及自然对流作用明显,10000 s时液相分数达到95%。放热工况以导热为主,60000 s时相变材料仅凝固了75%。从场协同效应分析,采用小尺寸热源管能缩短时间,但单位面积换热强度有明显下降。换热温差≤20℃时,其强化效果开始衰弱。     

Piecewise constant strain kinematic model of externally loaded concentric tube robots

This paper presents a piecewise constant strain kinematic model for concentric tube robots (CTR) in externally loaded conditions. It discretizes the pre-curved tubes comprising the robot into a finite number of pieces and involves external effects as a set of wrench vectors exerted along the robot backbone. Constant strain lets us describe the pieces with helices in which shear deformation and elongation are neglected. The resulting piecewise helix is the simplest curve that can catch the torsion of tubes that play a crucial role in kinematic behavior. This approximation transforms the conventional boundary value problem (BVP) of CTRs models into a set of nonlinear equations that drastically decreases the model resolution time. The present method uses a Lyapunov function and torsional Jacobian to ensure the distal torsion constraint consistently and, as a result, the solution’s convergence. The paper’s primary purpose is to present a fast, numerically stable, and relatively accurate kinematic model not reliant on measurement data. Experimental results on a two-tube prototype and provided for different tip loading conditions reveal maintaining a balance between adequate accuracy and reasonable running time, about 7 ms for five pieces per section, for real-time applications in the presence of external load.